Why does my gas fireplace keep burning out?
One of the main reasons why your gas fireplace keeps shutting down is likely due to the pilot light. This is an integral part of a gas fireplace, that kick starts the gas fire. When you turn on the fire, the pilot light button needs to be held in so that it can light the fire.
How do you adjust the flame on a gas fireplace?
How to Adjust a Gas Log Fireplace Flame
- Locate the gas log control knob.
- Release the control knob and allow the flame to burn for one minute.
- Turn the control knob to the left to increase the flame height.
- Monitor the flame height as the room warms.
How do you service vent free gas logs?
1) The first thing you will need to do is get a vacuum with a hose and preferably a brush on the end of the hose. 2) Using the vacuum remove the surface dust from the bottom of the fireplace around the gas log burner then remove the log set from the burner and do the same.
How do you clean the pilot light on a gas heater?
How to Clean a Pilot Light
- Cut off the gas to your furnace.
- Remove the pilot light and thermocouple assembly.
- Use your pliers or wrench to remove the pilot light and thermocouple from the bracket.
- Using the wire brush, brush away the carbon buildup and soot from both components.
How do you clean clogged burners on a gas fireplace?
Use a handheld vacuum cleaner to remove loose soot from the burner. Scrub the burner ports with a soft brush or toothbrush. Use compressed air to clear debris from the burner ports. Vacuum a second time to remove newly loosened debris.
Should gas fireplace burn blue or yellow?
Proper Flame Colour A gas fireplace should burn flames that are blue, perhaps with very small tips in yellow or orange. The flames should be steady and consistent no matter what.
How high should the pilot light be on a gas fireplace?
Inspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
Can gas logs be cleaned?
Cleaning Gas Logs Use a damp rag or lint-free cloth to wipe off the soot, carbon, and dust from the logs, at least once per year. Be careful to avoid scratching the logs, or they will no longer be useable. Liquid gas log cleaners are also available at your local fireplace dealer and may make it easier to clean.
Do ventless gas fireplaces need to be cleaned?
Your vent-free gas fireplace must be cleaned and serviced a minimum of once per year. Prior to the burning season, and additional cleaning in the middle of the season is recommended if the appliance is used heavily or it is located in an area of heavy traffic, dust, dirt, or pet hair.
How do you clean a clogged pilot light?
Use your pliers or wrench to remove the pilot light and thermocouple from the bracket. Using the wire brush, brush away the carbon buildup and soot from both components. For hard to reach areas and stubborn buildup, use the metal file. Wipe away dust with a soft cloth or burst of compressed air.
Why does my pilot light not stay on?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Does Lowes sell Cedar Ridge hearth logs?
Cedar Ridge Hearth 24-in 30,000-BTU Dual-Burner Vent-Free Gas Fireplace Logs with Thermostat in the Gas Fireplace Logs department at Lowes.com Shop cedar ridge hearth 24-in 30,000-btu dual-burner vent-free gas fireplace logs with thermostat in the gas fireplace logs section of Lowes.com
Is the log set approved for ventless heaters?
This log set has been tested and approved to ANSI Z21.11.2 standard for Unvented Heat- ers and can be operated with the flue damper closed. State and local codes in some areas prohibit the use of vent-free heaters. SAFETY PILOT This heater has a pilot with an Oxygen Deple- tion Sensing (ODS) safety shutoff system.
What should I do before shipping my logs and heater?
2. Remove all protective packaging applied to logs and heater for shipment. 3. Check all items for any shipping damage. If damaged, promptly inform dealer where you purchased the heater.
How do you set up a crhd18t log set?
Model CRHD18T (18″ Log Set) Log #1 Figure 19 – Installing Log #1 1. Place log #1 onto rear grate bracket (see Figure 19). 2. Place log #2 and log #3 onto middle grate bracket (see Figure 20). 3. Place log #4 and log #5 onto front grate bracket (see Figure 21). 4. Place logs #6, #7 and #8 as shown in Figure 22.