How can I configure BSNL mobile WiFi modem?

How can I configure BSNL mobile WiFi modem?

Wireless

  1. Click on “Wireless.”
  2. A new screen will open by showing all the information about Wireless.
  3. Tap the bubble on access point ACTIVATED.
  4. Go to SSID field to name Wi-Fi network.
  5. Go to “pre-shared key” field which shows “12345678″ as the default password.

How can I configure my new BSNL broadband modem?

Modem configuration:

  1. In the Internet Explorer, type 192.168.1.1 and press enter.
  2. Type username as admin and password as admin and press OK.
  3. Click “Advanced Setup”
  4. Click Edit button against VPI/VCI -0 and 35.
  5. Click Next in the above screen.
  6. Select PPP over Ethernet (PPPoE) in the above screen.

How do I configure my ADSL modem?

  1. Open up a web browser and type in theIP address of the DSL-300T (default is 192.168.
  2. Enter the Login nameand password (default is admin/admin).
  3. Click on the Setup tabat the top.
  4. Configure the following for yourconnection:
  5. Click on the Statustab at the top and then click on Connection Statuson the left side.

How do I setup my FTTH modem?

Configure BSNL Huawei FTTH ONT at 192.168. 100.1 IP Address

  1. Select 2_INTERNET in WAN connection to configure FTTH Internet.
  2. Type VLAN ID as 10.
  3. Select 802.1p as 0.
  4. Select IPGetMode as PPPoE.
  5. Enter allotted FTTH username and password.
  6. Click Apply.

How can I get BSNL APN settings?

How to install BSNL APN settings manually?

  1. Open the home screen of the mobile.
  2. Click on Menu button.
  3. Tap the Settings.
  4. Click on Mobile networks.
  5. Tap the Access Point Names.
  6. Click on ADD button displayed on the top right corner.
  7. Tap the Name field displayed and entered the name as you desired.

How can I reset my BSNL WiFi modem?

Login

  1. Login. Type 192.168.1.1 on the address bar of your browser and press enter. Enter admin as username and password.
  2. Click on the Admin tab.
  3. Click on Reboot.
  4. Select the factory settings and click on reboot.

How do I configure my modem?

Using any device with a browser, connect to the WiFi network of your modem. Open the browser, and enter the gateway address written on the back of the modem (this is commonly a string of numbers, such as 00.13. 11.189). Then enter your modem username and password, which should also be on the modem.

How do I configure my router?

About This Article

  1. Connect the router to the modem.
  2. Connect the computer to the router.
  3. Go to the router’s default IP address in a browser.
  4. Sign in with the default username and password.
  5. Open the Wireless settings.
  6. Name your network.
  7. Set an encryption type and passphrase.
  8. Save your changes.

How do I re configure my modem?

  1. Connect to your network wirelessly, or via ethernet.
  2. Find your router configuration page.
  3. Log in with the username and password.
  4. Find the Wireless Settings page.
  5. Set the new channel, usually with a dropdown menu.
  6. Your router will now reboot.

How do I configure my modem router?

Power on your router and computer first and then modem.

  1. Log into the router’s web-based management page.
  2. Configure WAN Connection Type.
  3. Enter your PPPoE username and password which are provided by your ISP.
  4. Click Save to save your settings, then the router will connect to Internet after a while.

How configure BSNL FTTH syRotech modem?

syRotech ONU Configuration Steps

  1. Click Internet Connection and select the following.
  2. Connection Name: 1_Internet_R_VII.
  3. Mode: Route.
  4. IP Protocol Mode: Ipv4.
  5. Select PPPoE.
  6. Enable NAT, VAN.
  7. Enter FTTH Username and Password provided by ISP.
  8. Enter Service Name: BSNL.

How do I configure my modem for internet?

NetLink ONU Configuration at 192.168. 1.1 for FTTH Voice & Internet

  1. Login to Netlink ONU in any browser with url 192.168.1.1.
  2. Enter username and password.
  3. Go to Management > Device Management > Restore default > Restore Factory default.
  4. Click Network > Internet > Delete.
  5. Check Status > Wan Connection info >