How do you start the first row of vinyl siding?
5 Easy Steps to Install Vinyl Siding Starter Strips
- Step 1: Find the Lowest Point of the Wall.
- Step 2: Drive a Nail Into the Marked Point.
- Step 3: Tie a String Around the Nail.
- Step 4: Measure the Widths of the Corner Posts.
- Step 5: Position the Starter Strip.
- Step 1: Create a Seal for Air and Moisture.
- Step 2: Cut the Trims.
How does vinyl siding interlock?
Vinyl siding panels are interlocked at their top and bottom edges via J-shaped channels called buttlocks. Each panel overlaps the panel below it and locks into place along the buttlock joint. Use the zip tool to release the buttlock at the top and bottom of the piece you want to remove.
How should vinyl siding be staggered?
Stagger the siding end laps so that no two courses (rows of panels) are aligned vertically, unless separated by at least three courses. Always overlap joints away from entrances and/or away from the point of greatest traffic. This will improve the overall appearance of the installation (Fig.
How far apart do you put seams on vinyl siding?
Plan overlaps where they’ll be the least visible, and stagger joints at least 2 feet from course to course, which will add to the siding’s stability.
Do you start siding from top or bottom?
Use the Wider Starter Strip The bottom of the starter strip (the part the bottom panel hooks on to) should be at least 1 in. below the top of the foundation, but the lower the vinyl siding is installed, the better. It protects the sheathing from rain, snow and pests.
Does vinyl siding have to be nailed to studs?
Sheathing/Backerboard Vinyl siding must never be applied directly to studs without sheathing.
How do you secure a top piece of vinyl siding?
Step 1. Snap the second-to-last piece of vinyl siding into place. Loosely secure it with galvanized roofing nails or exterior screws in the center of the notches on the top of the siding. This will be the last full piece.
How do you hang a top piece of vinyl siding?
Grip the cut edge of the top siding piece with the snap lock punch. Squeeze the punch until it pierces the vinyl and forms an exposed edge. Punch the whole length of the siding material every 6 to 12 inches. Put the siding piece into position.
How do you secure vinyl siding?
Vinyl Siding Installation Tips
- Allow for Expansion and Contraction.
- Choose the Right Nails.
- Don’t Drive the Nails Tight.
- Center the Nails in the Vinyl Siding Slots.
- Keep the Nails Straight and Level.
- Don’t Face-Nail.
- Never Pull Siding Taut When Nailing.
- Space the Nails Properly.
How do you install flashing over vinyl siding?
Nail the siding, stopping before placing the final nail at the end. Slide half of the piece of pan flashing, oriented vertically, under the end of the siding. Make sure the bottom of the flashing does not emerge at the bottom of the lap siding. Secure the flashing and the siding by fastening them to the structure.
How do you join clapboard to studs?
Nail the clapboard to the studs. If more than one clapboard is needed to span a wall, snap a chalk line between the marks on the corner boards on top of the course being overlapped. Join the clapboards with scarf joints as in Step 3.
Can you put vinyl siding over wood clapboard siding?
When installing vinyl over wood clapboard, vinyl siding has to be installed on a flat, smooth surface. It is also best to check and see if the clapboard siding has become warped from moisture or lapped; if so, you will need to level it with some vertical furring.
How do you measure clapboard for siding?
Starting at either end, make a series of marks along one edge, each equal to the clapboard’s exposure to the weather. For 6-inch siding, that’s 4 1/2 inches. Mark an arrow on the end of the stick where you began measuring. On the wall, snap a chalk line even with the windowsill’s bottom edge.