How wide is a Mustang rear axle?
How To Spot, Build, And Swap In the Ford 8.8 Mustang Rearend.
| Vehicle Application | Axle Width (inches) |
|---|---|
| FORD | |
| ’65-’66 Mustang | 57 11/44 |
| ’67-’70 Mustang 8.0 | 59 51/48 |
| ’71-’73 Mustang | 61 11/44 |
What is the width of a Ford 8.8 rear end?
7] From the factory, 8.8s use 1330- or 1310-series U-joints. This is the companion flange where the yoke bolts. The 1330 has a 3316-inch width for the U-joint, and the 1310 has a 358-inch width. The 1330 is usually found in Ford trucks.
What’s the difference between 7.5 and 8.8 Ford rear end?
The top and bottom of the 7.5-inch gasket are straight with rounded sides. The 8.8-inch gasket has flat sides, top and bottom, with rounded corners.
What rear end is in a 99 Mustang GT?
The ’99-01′ & ’03-04′ Mustang SVT Cobras were equipped with an Independent Rear Suspension (IRS) that used the Ford 8.8” differential. Starting in 2011, both the V6 (3.7L) & V8 (5.0L Coyote) Mustangs used the Ford 8.8 rear end.
How wide is a 66 Mustang?
How wide is a classic Mustang?
| Mustang 1964½–1966 | |
|---|---|
| Wheelbase | 108 in (2,743 mm) |
| Length | 181.6 in (4,613 mm) |
| Width | 68.2 in (1,732 mm) |
| Height | 51.2 in (1,300 mm) |
What rear end is in a 67 Mustang?
1967 Ford Mustang Axle Information & Ratios
| Axle code | Ratio & type |
|---|---|
| F | 2.80 locking differential |
| 2 | 2.83 open differential |
| B | 2.83 locking differential |
| 1 | 3.00 open differential |
How wide is a Dana 44?
These Dana 44s are an almost perfect swap for the rear of any TJ, YJ, XJ, ZJ, WJ, or even a KJ. At 60 3/4 inches wide, this axle is almost the same width as a TJ (61 1/2 inches, wheel-mounting surface to wheel-mounting surface). They are commonly found with Trac-Lok limited slips and either 4.30 or 4.56 gears.
How wide is a 2005 Mustang rear end?
It was also used in V8 equipped Mustangs from 1986 to the 2014 model years; and all Mustang models froM2011-2014. The ford mustang uses different size rear ends, 79-93 mustangs use a 57 inch wide rear axle. 94-98 Mustangs use a 58.5 Inch wide rear axle. 99 And newer mustangs use a 59 7/8 inch wide rear axle.
How do I know if I have 8.8 or 9.75 rear end?
While the Super 8.8’s cover has a bulge for the ring gear, it’s not anywhere near as pronounced as the 9.75’s. Once you know what to look for, it’s pretty simple to tell the two rear ends apart. You’ll just have to throw on your reading glasses and take a look under your truck to figure out the difference.
What vehicles have a Ford 8.8 rear end?
Common Applications
- 1986-2014 Ford Mustang.
- 1982-2012 Ford F-150.
- 1982-1996 Ford Bronco.
- 2001-2005 Ford Explorer Sport Trac.
- 1991-2011 Ford Ranger 4.0L models.
- 1991-2001 Ford Explorer (Solid axle)
- 1985-2011 Ford Panther platform vehicles.
- 2012–Present Ford F-150 (Super 8.8, depending on engine and other options)
How do you tell the difference between a Ford 8.8 and 9?
There is a very fundamental difference between Ford’s 8.8- and 9-inch axles. I reference these axles based on the ring gear nominal outside diameter in inches. The fundamental difference between these axles is how the gears are supported and which end of the axle housing (front or back) that they are assembled from.
How wide is a 67 Mustang?
| Ford Mustang (MY 67) 200 Size, Dimensions, Aerodynamics and Weight | |
|---|---|
| Wheelbase : | 274.3 cm or 107.99 inches |
| Length : | 466.3 cm or 183.58 inches |
| Width : | 180.1 cm or 70.91 inches |
| Height : | 131.1 cm or 51.61 inches |