What does a motor sensor do on a washing machine?
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board.
How do you fix a washing machine sensor?
You may unplug and plug in the washer and turn the power on. Lift and close the lid about six times within 12 seconds to reset the unit. You can also reset your washer by checking your product manual. Start a new wash cycle and test the appliance.
How do you change a shift sensor on a Whirlpool washer?
Replace it by following these steps with replacement part #WPW10006355:
- Unplug the washer and turn off the water lines.
- Remove the water hoses from the rear of the machine.
- Set the machine on its front.
- Remove the shield.
- Remove the old shift actuator.
- Install the new shift actuator.
- Reinstall the shield.
What does F5 mean on a Cabrio washer?
Did you receive a F5 E3 lid unlock alert? The F5 E3 alert indicates there is issue with the lid lock. Do not force the lid open, as permanent damage could occur. Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid.
Can you reset a Whirlpool Cabrio washing machine?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I reset the sensor on my Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
What are the sensors in a modern washing machine?
Specific sensors can measure temperature, pressure, vibration, proximity and force. While a pressure sensor can monitor water level, a force sensor measures the payload weight at the beginning of the wash cycle. A proximity sensor verifies that the door is closed and latched before start-up.
What are the sensors and actuators of washing machine?
In a washing machine, the Hall Effect sensor is mounted onto a printed circuit board in the electronics panel or onto the frame of the appliance, and a magnet is mounted on the rotating dial. When the dial is turned, the magnet rotates and changes the magnetic field detected by the Hall Effect sensor.
How do I run a diagnostic on my Whirlpool washer?
Now you can do an automatic diagnostic washer cycle. You will need to start the diagnostics mode again, but this time turn the washer cycle knob right until only the “spin” light is lit and press “start”. The washer will do a quick cycle that will test all the washer functions.
Where is shift actuator on Whirlpool washer?
The shift actuator is to the left and slightly below the shield.
How do I know if my Whirlpool Cabrio washer is faulty?
Whirlpool Cabrio washers will display a variety of error codes whenever there is a problem with the washer. The error code will usually begin with either an F (Fault) or an E (Error), with a number next to the letter that indicates the faulty component or reason for the error code.
What does F mean on a whirlpool Cabrio washer?
An F error code usually means the washer will not work at all, and the control board will need to be replaced. Variations of the F error code are discussed at the end of this guide. This guide applies to most Whirlpool Cabrio models, including the following:
How do you fix a whirlpool washer that won’t turn on?
A short-term fix for an F error code can be to reset the control board by disconnecting the power to the washer for 5 minutes. However, this solution to the issue will likely only work if the error code is caused by a random glitch.
How do you remove the control panel on a whirlpool washing machine?
Disconnect the power to the washer. Disconnect the water hoses and move the washer to a suitable location. At the rear of the washer, locate three screws on the bottom of the control panel, and remove them. Tilt the control panel up and push it forward.
