What sizes do Schluter niches come in?
The shower niche features a 1/2″ (12.5 mm) -thick by 2″ (50 mm) -wide integrated bonding flange and is available in 12″ x 6″ (30 x 15 cm), 12″ x 12″ (30 x 30 cm), 12″ x 20″ (30 x 51 cm), and 12″ x 28″ (30 x 71 cm) sizes.
What is the standard niche size?
Positioning your niche at chest to eye-level is a good standard. This translates to a height of about 48 to 60 inches. Ideally, you’ll want to position your niche to fit between the studs which are usually located 16 inches apart. But many contractors can help you with planning the space for a more custom look.
How big should I make my shower niche?
It can look odd when your shower niche is tiny compared to the size of your shower. As a general rule, we recommend installing a niche that’s at least half the width of your shower wall.
Can a shower niche be too big?
How big should your shower niche be? Installing a shower niche that is too small is not even worth the effort. Your shower niche definitely needs to be large (both deep and tall) enough to hold the bulk-sized large bottles.
Is Kerdi niche waterproof?
Schluter-Systems has developed four prefabricated and completely waterproof shower niches that are ready to tile. Made of Schluter®-KERDI-BOARD, the shower niches are completely compatible with surface applied waterproofing systems, such as the Schluter®-KERDI and KERDI-BOARD shower assemblies.
How high should a niche be above a tub?
Shower Niche Height The ideal height for a bathtub shower niche sits at chest to eye-level when standing — a height of around 48 to 60 inches, as this height suits most adults. Set aside a 12-by-24 inch space between studs to hold shampoos, rinses, scrubbers and razors.
Do you need a shower niche?
A shower niche is a much better solution, for relatively little expense. It’s an extremely useful feature that provides you with a proper place to keep your shower accessories, without adding bulky organizers that take up much-needed space.
How high should a shaving niche be?
The standard shower niche height is between 36″ and 40″ off the shower floor (to the base of the niche). The typical or standard shower niche height for tub/ showers is between 25″ and 30″ (to accommodate bathers).
How thick is Kerdi in niche?
1/2-in thick
OVERVIEW. Kerdi-Board-SN is a prefabricated shower niche made of Kerdi-Board. It can be installed in Kerdi and Kerdi-Board shower assemblies. The waterproof niche has a 1/2-in thick by 2-in wide bonding flange and is ready to be tiled.
What is the size of a Kerdi fix niche?
Kerdi-fix is a urethane sealant made specifically for kerdi products and waterproofs seams. I am building a 2 foot high niche by 1 foot wide. Begin by cutting all the pieces to the appropriate size. The piece for the back of the niche will be the largest – 24 1/2” x 12″. When assembled this will give you an inside dimension of 24″ x 12″ x 3 1/2″.
How to install Kerdi niche flanges to drywall?
I lapped them by 3 inches. I covered the right side of the wall and the niche with the 2nd (top) piece of Kerdi and then cut it out with a utility knife after smoothing the sheet and Kerrabond underneath. 8 hours later the Kerdi was affixed to the drywall substrate with excellent coverage but did not seem to bond to the pre-fab Kerdi niche flanges.
What are the dimensions of a wall niche?
The piece for the bottom of your niche will be 12″ long by 3 1/2″ wide (4″ wall cavity minus 1/2″ for the thickness of the kerdi-board). The piece for the top of your niche will be 13″ long by 4″ wide. (It’s bigger than the bottom piece, you’ll see why shortly)
What are the wide silver screws holding my Kerdi board to wall?
I’ve found the kerdi board but the sales person said to use screws topped with a bit of silicone to hold the board to the studs. What are the wide silver (they look like washers ) holding your kerdi board to the wall? Roger They are the kerdi-board washers.