Can headphone out be used as line out?
You can use the headphone output of your device as a line out. A headphone out can be used to send line-level signals to other audio devices, provided the volume is not too high. This will help prevent distortion and reduce noise. Headphone outs can be used as substitutes for line outs.
Can I use headphone jack for subwoofer?
It should work fine. You will have to sum the two headphone channels together using resistors, but this may not be necessary because most headphone outputs just use resistors off the speaker outputs.
Can I connect line out to subwoofer?
But for shorter runs, any well-made cable will be fine. You will connect this cable from the subwoofer pre-out on your AV receiver to the LFE or mono line-level input on your sub. All subwoofers will have a low-level input of some description. Different brands will label this in different ways.
Can I connect subwoofer to line out of amplifier?
Locate the plug on your amplifier that is labeled Sub Out, LFE (low frequency effects) Out or Line Out [source: KEF]. This is the terminal used to connect the subwoofer to the amplifier. Connect the cable that was included with the subwoofer to the amplifier’s terminal.
Can I connect headphone output to amplifier?
Connecting headphones out to an amplifier’s line-in is ok. Audio won’t be as great, but it’ll not damage the amplifier or speakers. The voltage in headphones out connection isn’t all that high to damage a line-in. Headphones out connections have a low output impedance.
Can I use the headphone jack as an audio output?
So can a headphone output be a workable substitute for a line level output in other situations? Sure, in a pinch it will usually work okay. Headphone amps usually aren’t as free from noise and distortion as good line amps, but in many situations they can be used without significant degradation in overall sound quality.
Are headphones line level?
Line level signals are much hotter than microphone level. Aside from the output of a mic preamp, other examples of line level signals are the headphone output of your phone, the aux input on your car stereo, or the output of an audio mixer.
Can I use a headphone amp as a preamp?
Can you use a headphone amp as a preamp? In some cases, it may be possible to use a headphone amp as a preamp. To do so, the headphone amp would have to be capable of driving down to around 16 Ohms, or preferably even lower.
How do you hook up a subwoofer without output?
You can use your new subwoofer like a speaker if there is no preamp output on your receiver. To do it, run the speaker’s wire to connect the subwoofer to a receiver. Then click the front left and right speakers to the speaker terminals of the subwoofer.
Can you use tape out for subwoofer?
Subwoofers will work when plugged in the tape output. However, it will be at a fixed volume. And that’s because tape output is not affected by the main volume.
How do you connect headphones to a bass amp?
However, there are several solutions available that will allow you to play bass guitar through headphones, such as:
- using an amPlug headphone amp,
- using special amplifier headphones,
- plugging headphones into an amp,
- plugging into a laptop via an audio interface.
- plugging into your smartphone or tablet using an adapter.
How to connect a subwoofer to an amplifier?
There are a few ways that one can expect to connect a subwoofer to an amplifier, receiver, or processor (also known as a home theater receiver). The most common method is done by connecting the subwoofer to the SUB OUT or LFE output of a receiver/amplifier. But you might also come across a subwoofer that uses stereo RCA or speaker wire connections.
Will a line out subwoofer work with my speakers?
Yes that would work. Whatever sub you get will most likely have all of the crossover and level controls that you would need to match your speakers. All the line out is doing is sending a full range signal, (controlled by the volume control) to the the device hooked up to it.
How do I fix the line out on my subwoofer?
Take the xlr out of the DAC to the sub (use crossover and level adjustment on the sub) and RCA out of the DAC to the main speakers amp. would be nice to be able to cut some of the lows going to the mains, but it works fine this way also (crossover at 40hz on the sub.) it states that the line out is fixed.
How do you connect a subwoofer to an LFE cable?
Connect Using the LFE Subwoofer Output. The preferred method of connecting a subwoofer is through the Subwoofer Output (labeled as ‘SUB OUT’ or ‘SUBWOOFER’) of a receiver using an LFE ( an acronym for Low-Frequency Effects) cable.
