How do you make throw pillow covers?

How do you make throw pillow covers?

Instructions

  1. Cut the Fabric. Cut 1 rectangle from your fabric the size listed below corresponding to the size of the pillow insert:
  2. Mark the Rectangle. Measure the distance listed below in from each end along the longer top and bottom edges.
  3. Hem the Ends.
  4. Fold on the Markings.
  5. Sew the Seams.
  6. Turn Right Sides Out.

How do I make a no sew pillow cover?

How to Make a No-Sew Pillow Cover

  1. Measure and Cut Fabric. Measure and cut fabric three times as wide and two times as high as the pillow form (Images 1 and 2).
  2. Cover Pillow Form. Place form in the middle of the fabric piece, and fold over fabric in half to completely cover (Images 1 and 2).
  3. Tie a Knot.

How do you hand stitch a pillow?

Instructions:

  1. Cut out the front and back sides of the pillow.
  2. Pin the front and back sides together – with the right sides of the fabric together.
  3. Thread your needle, and start hand-sewing at the bottom edge of the pillow where your first pin is.

How do you make a simple cushion cover with a zip?

HOW TO MAKE ZIPPERED CUSHION COVERS | Sewing

  1. Step 1 – Measure and Cut.
  2. Step 2 – Sew One Side Leaving a Gap.
  3. Step 3 – Baste the Gap.
  4. Step 4 – Insert the Zipper Face Down.
  5. Step 5 – Remove the Basting Stitches.
  6. Step 6 – Stitch the Zipper Ends.
  7. Step 7 – Fold and Stitch.
  8. Step 8 – Press.

How do you make a simple envelope pillowcase?

Follow these easy steps to sew an envelope pillowcase.

  1. Cut fabric. Wash your fabric before you cut.
  2. Press back piece seam ½”. Fold one edge under ½”, press.
  3. Press edge under 1″. Fold previously pressed edges under 1″ and press again.
  4. Sew seam.
  5. Turn back pieces.
  6. Sew pillow.
  7. Trim corners.
  8. Finish raw edges.

How much fabric do I need for a 20×20 envelope pillow?

If your pillow is 20 x 20, measure a piece of fabric that is 19.5 inches wide by 46 inches long. The 19.5-inch width is for a 19-inch final cover size plus . 5 inch seam allowance.

How do you make a homemade pillow?

– Measure and Cut Fabric. Measure and cut fabric three times as wide and two times as high as the pillow form (Images 1 and 2). – Cover Pillow Form. Place form in the middle of the fabric piece, and fold over fabric in half to completely cover (Images 1 and 2). – Tie a Knot.

How to make a no sew pillow?

how to make a no sew pillow STEP 1: Iron all the creases out of the dish towel and place it wrong side up on a flat surface that it suitable for ironing on. STEP 2: Dry fit where you want to place the pillow by laying it on the dish towel, leaving room to wrap the bottom of the towel to within 3″ – 4″ of the top of the pillow.

How to make homemade pillows?

Make the Pillow Step 1: Cut the fabric. Using a ruler and pencil, mark two 4 1/2-by-10-inch rectangles on the wrong (nonprinted) side of the fabric. With a pair of scissors, cut along the marks to create the two panels needed for the pillow. Step 2: Sew the seams. Place the two panels’ right (printed) sides together, with the raw edges aligned.

How do you make a pillow cover with a zipper?

Add 1 inch (2.5 cm) to the height and length of the pillow insert for the seam allowance.

  • If the zipper is longer than the pillow opening,mark the zipper the same length as the opening.
  • Lay the zipper facedown on the opening seam,aligning the coils with the seam. Flip the zipper pull up,so that it can be moved down while you’re sewing.