What is the spark plug gap on a Homelite chainsaw?
a 25 thousandths of an inch gap
Remove the wire and boot from the spark plug. Use a socket or a spark plug wrench to help unthread the old spark plug. Before you install the new spark plug confirm that the spark gap is at manufacturer’s specifications. This chainsaw model requires a 25 thousandths of an inch gap.
What should the gap be on a chainsaw spark plug?
Most of the chainsaws have a 0.025 gap in their spark plug. Different manufacturers make different kinds of chainsaws. However, the basic structure is constant.
How do you adjust the carburetor on a old Homelite chainsaw?
Set the High-Speed Screw Adjust the Homelite chainsaw carburetor by turning the high- and low-speed screws as needed. Set the high speed screw by adjusting the screw marked “H.” Pull the trigger so that the throttle opens as wide as possible. Turn the screw to the left and note the engine performance.
What size chain does a Homelite XL 12 take?
16-Inch Chainsaw Chain Replacement for Homelite XL-12 – (16″, 3/8″, . 050″, 60 Drive Links)
Who makes Homelite chainsaw?
Techtronic Industries
John Deere acquired the brand in 1994. Techtronic Industries acquired Homelite from John Deere in 2001. Homelite has shifted its production primarily to consumer level lawn and garden equipment and light duty chainsaws.
What is spark plug gap?
Importance of the Spark Plug Gap The gap is the distance between the center and side electrodes, set so arcing occurs at the proper voltage that ignites the fuel and generates the combustion that makes the engine run.
How much do I GAP my spark plugs?
between 0.020 and 0.040 of an
For most racing applications, you usually want the plug gap to be between 0.020 and 0.040 of an inch. Most engine builders seem to settle around 0.035 of an inch. Factors such as the type of ignition you run, cylinder heads, fuel and even timing can affect how much gap will work best for you.
What are the L and H screws on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
What size chain does a Homelite XL use?
The chain on the Homelite XL is a Homelite Raker38 III and an Oregon 72. The chain pitch is 3/8 inch. Two guide bars can be used with this chain saw. The short guide bar is 16 inches long, and the long guide bar is 24 inches.
What size chain does a Homelite chainsaw use?
Within Homelite Chainsaw Chains, bar length options include 16 in., 14 in. and 18 in. What is the top-selling product within Homelite Chainsaw Chains? The top-selling product within Homelite Chainsaw Chains is the Powercare Y56 16 in.
What is the air gap on a Homelite chainsaw?
The air gap for Homelite chainsaws will range from model to model but is usually between .2 mm to .35 mm. You can use a feeler gauge or a plastic shim to set this distance. The magnets on the flywheel must be clean and show no signs of discoloration.
How do I adjust the timing on a Homelite chainsaw?
The timing on Homelite ignition systems is fixed and can’t be adjusted. On Homelite chainsaws it’s set to 27 degrees before top dead center, which refers to the piston’s stroke on the crankcase. Since no internal wear can happen on the timing, you won’t need to worry about adjusting it.
What size spark plugs do I need for a Homelite chainsaw?
The spark plugs need a gap of .025 inches to function properly. If this gap is off or the metal tip is corroded or bent, the spark can’t fire a sufficient charge to ignite the fuel. The type of spark plug used in Homelite chainsaws is a standard two-cycle engine plug; any brand will be sufficient as long as it meets the gap recommendations.
What are some common problems with Homelite chainsaws?
Some Homelite chainsaws have a plastic stopping device that limits adjustment of the low and high speed screws. The company recommends taking a faulty chainsaw to an authorized repair center if the chainsaw’s speed cannot be properly adjusted with a slight twist of either screw.