Table of Contents
Why is my Whirlpool washing machine not spinning?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
How do I reset my Whirlpool Ultimate Care 2?
The following steps should be used to reset your Whirlpool washing machine:
- Turn off the washer.
- Turn the mode dial to NORMAL.
- Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
Why is my washing machine washing but not spinning?
Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
Why won’t my Whirlpool washer agitate or spin?
Common solutions for: Whirlpool Washer won’t spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washer transmission.
How do you fix a washing machine that will not spin?
- Redistribute an off-balanced load of laundry.
- Level an off-kilter washer.
- Check the power source.
- Stop using an extension cord.
- Inspect the spin switch.
- Stick to high efficiency detergent with a front-load washer.
- Undo any kink in the hose.
- Track down a blockage in the drainage system.
How do you reset the spin cycle on a Whirlpool washer?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
Do Whirlpool washers have a reset button?
There is no Reset Button on your Whirlpool Washer. Luckily, you can reset the washer in several easy steps. If you need to reset your Whirlpool Washer and, since there is no reset button, first unplug the washer. After two minutes, plug the washer back in.
Why is the spin cycle not working?
If the spin cycle doesn’t work, the belt may be loose or broken. Tighten or replace the belt. 2. Check the lid switch and the tab on the lid that strikes it.
How do I reset my Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:
- Turn the washing machine off using the control panel.
- Unplug the washing machine.
- Wait three minutes.
- Plug the washer back in, and wait thirty seconds before turning the washer on.
How do you reset an automatic washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I reset the control panel on my Whirlpool washer?
Why won’t my Whirlpool Ultimate Care II washer spin?
Why Won’t Your Whirlpool Ultimate Care II Washer Spin? The most likely reason for your washer to refuse to spin is a blocked drain hose. One thing to check is that the drain hose is not over 96 inches from the ground. Even excess suds can create issues with the spin and drain cycle.
Why is my Kenmore Elite washer not spinning?
The most likely reason for your washer to refuse to spin is a blocked drain hose. One thing to check is that the drain hose is not over 96 inches from the ground. Even excess suds can create issues with the spin and drain cycle.
What happens when the clutch on a whirlpool washer goes bad?
Typically when the clutch is bad the washer will wash, will pump out but will not spin or spins slowly. This video will show how to replace the clutch on a Whirlpool direct drive washer.
Other things that can cause the washer to wash but not spin are the timer, water level control and transmission. If the timer or the water level control is bad, you will not hear the motor trying to run when it’s in spin.
